Re: [Chrysler300] Chrysler 300H idle speed
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Chrysler 300H idle speed





Thanks Gary, as I said in one of my responses, I did have it rebuilt by the Philbin Group and it looked to be a comprehensive job. It makes it hard for me to think it’s a dis problem for that reason, but it is on my list to validate by substituing another distributor. As someone else said, the fact that the RPM “hunts” between 600 and 700 rpm
engine speed makes the distributor suspect.

Thanks, MIke Moore
300H

  
On Oct 25, 2015, at 11:23 AM, Gary Nelson <gnelson@xxxxxxxxxxxx> wrote:

I highly recommend any old distributor with unknown history, MUST be rebuilt and setup on a dist. machine. I highly recommend the Philbin Group in Portland OR, 1-800-869-7301, talk to Mark. If I remember correctly, The charge for basic rebuild was $75. Also, they can rebuild or replace vacuum advance.  I installed and recommend electronic ignition.
Note: with electronic ignition you must pay special attention to the voltage out put at the resistor. To high and you will fry the electronic component.  I may mention Philbin is fast and courteous. I am sure there are many qualified to do rebuilds. Any of them are UPS away.
 
Happy Sunday,
 
Gary Nelson
AKA, The Parts Doc
 
 
 
Sent: Saturday, October 24, 2015 10:10 AM
Subject: Re: [Chrysler300] Chrysler 300H idle speed
 
 

Michael,
A "hunting" condition at any idle speed can be caused by a defect in the centrifugal spark advance mechanism in the distributor, usually a weak (stretched)  or broken spring.  Don't overlook that as a possibility after checking more obvious things that are easier to get to.
---------Marshall Goodknight


---------- Original Message ----------
From: "Michael Moore mmoore8425@xxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx>
To: Ron Waters <ronbo97@xxxxxxxxxxx>
Cc: chrysler300@xxxxxxxxxxxxxxx
Subject: Re: [Chrysler300] Chrysler 300H idle speed
Date: Sat, 24 Oct 2015 10:04:51 -0700

 
Yes, it idles especially rough the lower it goes. It also seems to “hunt” between 500 and 600.
I discovered a couple of vacuum leaks yesterday and thought I had fixed them by removing the base gaskets from the carburetors, cleaning them, and forming a very small (cross section-like a pencil lid) of form-a -gasket  on all 8  surface and reassembled them. It’s hard to believe I still have a vacuum leak but certainly possible. There was also an old smog kit tap into the intake manifold I resealed.
Thanks, MIke Moore 300H
 
 
On Oct 24, 2015, at 9:41 AM, 'Ron Waters' ronbo97@xxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 
 

Not sure what you mean by 'marginal'. Does the car run rough and act like it's gonna stall ? If so, I would attach a vacuum gauge to the intake and see what's going on. Problem is either a vacuum leak, or something is out of whack in your carbs. It's not Ethanol gas.
 
Ron
----- Original Message -----
Sent: Saturday, October 24, 2015 12:30 PM
Subject: [Chrysler300] Chrysler 300H idle speed
 
What idle speed are the 300H folks setting? Although my manual says 650, it sure is marginal at that speed. 800 feels better, but I don’t understand what causes the difference. Ethanol? 
 
Thanks,
Mike Moore
300H
 
 
 
 
 
On Oct 24, 2015, at 7:49 AM, Robert Augliera raugliera@xxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 
 
 
Does anyone have tips on replacing a windshield on a 61 Chrysler. Lots of chrome to remove.
Thanks
Rob
 
 
 
 
 


____________________________________________________________
MailFilterGateway has detected a possible fraud attempt from "thirdpartyoffers.juno.com" claiming to be Heavy rains mean flooding
https://ad.doubleclick.net/ddm/clk/296043998;123050234;f



__._,_.___

Posted by: Michael Moore <mmoore8425@xxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang





__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.