Re: Poly 4 bbl Setup

[Bill <Y1TopBanana73@xxxxxxxxx>]

${top_text_ad}
Sean,

Only problem with using NO spacer is if you have an early WCFB
manifold. There's basically no way to bolt a modern carb to that
manifold without it. The bolt pattern for the manifold is WAY too
small. I'll round some pics up for you too.

Bill M
65 Coronet 500 'vert

On Sat, Mar 7, 2009 at 11:27 PM, sean dietz <dietz_diggler@xxxxxxxxx> wrote:
>
>
> Thats great Bill, glad you got yours worked out. I wouldn't mind a picture of your throttle linkage and kickdown. I'm going to rout out the rear ports on the intake and use an edelbrock carburetor, without a spacer, but I'd like to have the picture just in case I change my mind later. Now that I think about it I've got an edelbrock nitrous plate kit thats been laying around for a few years... hmmmmm...
> Send it to my e-mail if you can, I'd appreciate it.
> Dietz
>
> --- On Sat, 3/7/09, Bill <Y1TopBanana73@xxxxxxxxx> wrote:
>
>> From: Bill <Y1TopBanana73@xxxxxxxxx>
>> Subject: Re: Poly 4 bbl Setup
>> To: 1962to1965mopars@xxxxxxxxxx
>> Date: Saturday, March 7, 2009, 9:30 PM
>> I ended up having enough throttle cable today when I put the
>> bracket
>> back down in it's stock location. I am however going to
>> have to modify
>> the goalpost. We figured out that I'll cut a piece off
>> the 2nd one I
>> have and weld it onto the original essentially making a
>> double goal
>> post. Since the carb is wider and it pushes the kickdown
>> outward, this
>> will keep it from hanging and flopping around.
>>
>> I'm using an adapter from Trans Dapt. It works well but
>> you'll have to
>> finish it. The holes where it mounts to the manifold are
>> not drilled.
>> Drill the holes and get a counter sink. Drill out the top
>> of the
>> adapter until you can put 45 degree shoulder allen head
>> screws are
>> flush.
>>
>> If anyone wants pics, I can take some. It was surprisingly
>> easy once I
>> figured it out.
>>
>> Bill M
>> 65 Coronet 500 'vert
>>
>>
>> ----
>> Please address private mail -- mail of interest to only one
>> person -- directly to that person.  I.e., send parts/car
>> transactions and negotiations as well as other personal
>> messages only to the intended recipient, not to the
>> Clubhouse public address. This practice will protect your
>> privacy, reduce the total volume of mail and fine tune the
>> content signal to Mopar topic.  Thanks!
>>
>> '62 to '65 Mopar Clubhouse Discussion Guidelines:
>> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
>
>
>
> ----
> Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>

${bottom_text_ad}
----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.

This email was sent to: ${recipient}

u/?bUrDWg.${encoded_sub_id}.${EMC}