Re: ball and trunion vs u joint
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: ball and trunion vs u joint



I couldnt find the kit in NEAPCO 's catalog (http://www.neapco.com/n_products-catalogs.php)

I do know that Bernbaum or Atlas should have a kit, usually for around $75. You would need to contact them as they dont list the '62-65 parts on their site. Also, any local driveline shop worth its weight should be able to get one within a day or two, if they dont already have a kit on the shelf.

http://www.oldmoparts.com/NAVIG.htm (bernbaum's)
http://www.atlaschrys.com/Clutch.html

--Tom

On 12/27/2010 4:12 PM, Leslie Thrasher wrote:

I will throw this tidbit out there and you can do what you want with it! I worked as a buyer for Mopar Parts in the 70's and was responsible for the Detroit Universal Division (DUD) buying and inventory control. At that time I was buying the assembled kits from a company in Pottstown, PA called NEAPCO. They were doing the casting and machine work on the housing. Do not know anything about them now or whether they are still in that business or not. Good luck with your search!!!

--------------------------------------------------
From: "Butch Edison" <waedison@xxxxxxxxxxx>
Sent: Monday, December 27, 2010 4:47 PM
To: <1962to1965mopars@xxxxxxxxxx>
Subject: RE: ball and trunion vs u joint


I did not find a vendor selling ball & trunnion kits for our cars. If you do find one, please let us know who it is. After a couple years of searching, I did find some old rebuild kits and bought a few. The rubber boots were still good, but the needle bearings in the cups, well, some were a bit rusty. Your note reminds me to take them to a bearing shop today and see if I can get
new needle bearings or if they can provide the complete U-joints.
Fortunately for me, my ball & trunnion U-joints were still in good shape, just needed to replace the rubber boot, which is very hard to come by (at least it was for me). Some of our members had had luck I think using some VW rubber boots. Whatever you use, be sure to grease the heck out the rubber
boot and then nurse it on, as it can be torn.

Again, if you find a vendor, please let us know. Those old B&T U-joints were
used all the way up the Mopar food chain to the Max Wedge cars. I have a
friend who drag raced those MW cars for Chrysler in the 60s and 70s as a
team driver and he had no problems with them.

/Butch/Ferndale, WA

-----Original Message-----
From: laborboy@xxxxxxxxxxxxx [mailto:laborboy@xxxxxxxxxxxxx]
Sent: Sunday, December 26, 2010 7:05 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: ball and trunion vs u joint


Need to replace the old B&T joint in our 1964 Dodge 330. Has anyone had
work done by SharaDon in Minnesota, or Inland Empire Driveline in
California? Seems like the replacement slip joint set up vibrates more.
Any tips?

Zack and Ileana in Chicago


----
Please address private mail -- mail of interest to only one person --
directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.




----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.