RE: 318 Poly refresh time - Cam and gear drive info, please
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: 318 Poly refresh time - Cam and gear drive info, please



Not worried about the distributor. I've dropped in an electronic distributor and all from a mid-70's pickup. Chrome ECM, which is kinda pointless on the existing 2-bbl carb, as I could never get enough flow through that carb to allow 6,000 RPM. At any rate, it runs like a charm. So while I may have someone look at changing the curve (after we see how it works in the new engine), I'm probably just going to stick with that set-up.

I am, however, raising my eyebrows a bit at reported mileage. I'm already getting ~22.5 miles/U.S. gallon, and was hoping to better that. I've had no shortage of cars that got better mileage, including a '67 Newport with 383 4-bbl factory single exhaust, '71 Polara 318 2-bbl factory single exhaust, '57 Dodge Mayfair 303 2-bbl 3.5" exhaust w/340 mufflers, etc... All stock engines. I was hoping that with the right cam, the dual exhaust, and the electronic ignition, I would be abler to get closer to 30 MPG. When I got the car, it had a 6 1/2 cylinder 318 poly (yes, one completely dead, one half dead cylinder) with exhaust that nicely matched the blue interior, and it got over 20 MPG. The engine I have right now was a low hour rebuild from a farm truck, running one car & one truck head.

-Ray


-----Original Message-----
From: 1962to1965mopars@xxxxxxxxxxxxxxxx [mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of gto64gto@xxxxxxxx
Sent: June-02-14 2:02 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: Re: 318 Poly refresh time - Cam and gear drive info, please

Ray, I had a new 65 Belverdere11 with 318. 3-speed, 3.23 gears in school. I installed a 58 318 cast 4 barrel carb intake and the 58  AFB. I installed duals with turbo mufflers and a floor shift. It ran OK but not that great. 
In 65, no one made advance kits. I pulled the distributer and slotted out the advance weight slots and used needle nose pliers to stretch the advance springs some. I left the vaccumn canaster stock and connected. I really got lucky with that combo. I could outrun any 383 auto or 4-speed from 0 to 100. 
I never got beat. My milage was 21-22 mpg. I would suggest keeping what you have, less gear drives, pay close attention to your valve adjustment and send your distributor to Don at FBO Systems to have your distributor recurved and set up. I think you'll be surprised and pleased at the power and good gas millage you'll have.  Hope this helps


-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.