Re: IML: 727 leak
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: 727 leak



Thx  Stevan and Dave,

The shaft end looks to be blocked only by a useless ear of the tailshaft. It appears like the designers put it there by accident which prevents me from sliding the shaft rearward no more that about 1/2" . I wonder if the o ring is within 1/2" of the end? Is the shaft stationary or does it move on it's axis or forward and aft?

Thx guys,
Chris
67 Imperial Convertible
----- Original Message ----- From: "Stevan Miner" <miner@xxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Sunday, December 17, 2006 6:27 AM
Subject: Re: IML: 727 leak


Hi Chris,
What you have leaking is the O-ring on the end of the shaft that the low-reverse servo arm pivots on. You can change this without trans removal but it takes a little work. You'll have to remove the tailshaft. Remember there is a snap ring under the cover that is now hidden by the rear transmission mount. The pan and valve body will also have to be removed. You can then take a long punch from the inside of the case and tap that shaft rearward to get at the offending o-ring. I never completely remove the shaft just enough to replace the O-ring. Makes it alot easier to line everything back up and less chance of dislodging the reverse band strut link. I always replace as the seals and gaskets that were distributed during the procedure including the selector shaft seal.
Stevan Miner
Miner Auto Service
Winnebago MN
----- Original Message ----- From: "Chris Strohmeyer" <chrisstroh@xxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Sunday, December 17, 2006 12:45 AM
Subject: IML: 727 leak


This is going to be hard to describe but here goes. On my 67 Imperial I have a leak at just below the vertical surface that the tailshaft bolts to. It's a small space between the lower flange of the tailshaft and the TOP of the oil pan FLANGE. To see it you have to look from the back of the transmission looking forward. It's slightly off center of the tailshaft and where it's leaking appears to look like the end of a aprox 3/4" diameter shaft. Oil is seeping from this "shaft end". I've looked at the breakaway photos of the 727 and see nothing that looks like this inside so my next step is to drain the tranny,pull the pan and see.

Does anyone know what I'm talking about?

Thx,
Chris Strohmeyer
----- Original Message ----- From: "Robin Giesbrecht" <robings@xxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Saturday, December 16, 2006 9:59 PM
Subject: Re: IML: power steering leak - O rings


You can buy rebuild kits for the power steering pump that are really only a seal kit. There is a big oring that seals the whole canister and a few more seals for the shaft and the relief valve I think. Not that hard to do.

Robin Giesbrecht
72 Imperial


From: Kenyon Wills <imperialist1960@xxxxxxxxx>
Reply-To: mailing-list@xxxxxxxxxxxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: Re: IML: power steering leak  - O rings
Date: Sat, 16 Dec 2006 21:26:56 -0800 (PST)



--- Chris Strohmeyer <chrisstroh@xxxxxxxxxxx> wrote:

> Kenyan said...........
>
> 4.  "Bad o-rings"?  Anyone else that works on cars
> where you live?  That sounds like bad advice to me,
> but it may be out of context and part of other info
> that he gave?
>
> Aren't there 1 or 2 large o rings on the power
> steering pump that seals the
> reservoir can?
>
> Chris



True.  There are o-rings.  The way that the thing's
put together sorta precludes catastrophic fluid loss
as described in the letter posted here, but to address
the question:

If I were going to pay a mechanic to deal with this, I
would buy a replacement pump unit that comes with a
warranty so that I didn't have to worry about it.

Reason being that I don't agree with paying a mechanic
to only partially rebuild a pump for a labor charge
that could very likely equal or exceed the cost of a
replacement.  I would pay the rehab factory that will
give a warranty do that portion instead and get the
whole thing spec'd out by someone that does nothing
but.  That's what I'd do, anyway.

Also, a failed O-ring seal is highly unlikely to cause
the sort of rapid fluid loss described, so that's what
I was thinking based on the info given, but I wasn't
there.


Please use an o in my name.  I'm particular about
that.


-Kenyon



____________________________________________________________________________________
Do you Yahoo!?
Everyone is raving about the all-new Yahoo! Mail beta.
http://new.mail.yahoo.com


-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm


_________________________________________________________________
Download now! Visit http://www.telusmobility.com/msnxbox/ to enter and see how cool it is to get Messenger with you on your cell phone. http://www.telusmobility.com/msnxbox/



-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm





-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.