[FWDLK] Fwd: [FWDLK] The Testies......
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[FWDLK] Fwd: [FWDLK] The Testies......



Hey all I have been told by an old trans guy that my pushbutton had been tweeked by an old timer due to the way it hits second nice and sound not at all slushy like they were from the factory did. So when I grilled him for more info I got the blow off and told I wouldnt understand it anyway. The reason I am mentioning from an earlier chat Neil had mentioned something about the D-500 shift points being moved up. I think this is what hade been done with my 59 and it does shift good and solid.
 
Jimmy




See what's new at AOL.com and Make AOL Your Homepage.

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

--- Begin Message ---
  • From: eastern sierra Adj Services <esierraadj@xxxxxxxxx>
  • Date: Thu, 8 Nov 2007 09:50:29 -0800
Hey, John; no, no attack at all!

Scientific inquiry demands close vetting.

This is what Hot Rod (5/56;p. 26) has to say:

"The standard sybchromesh sideshift gearbox used on D500's  is a heavy
duty unit with the following ratios: R: 3.2, L: 2.5, 2nd: 1.68,
High-Direct [presumably: 1.00]. These ratios have been used on all
Chrysler products for many years and one would think that for a gigh
performance car, more compatible intermediate ratios would be used; say
about a 2.3 Low and a 1.3 second But, alas, ! Such is not the case."

SO; You're RIGHT; I was looking at only part of the story; and those
numbers had merely jumped-out at me!


HERE WE GO: from earlier on Page 26 : 

"The D-500 gear ratios, mechanical pushbutton layoiut and 'kickdown'
feature are identical with the Plymouth, except the maximum converter
ratio at stall speed, which for the D500, is 2.71 @ 1850rpm..

And:..." D500 Powerflite had shift points raised somewhat for better
performance. Full throttle  shifts from Low to High  in Drive  were made
at about 70 mph, instead of about 55 mph for standard Dodges."

So, go plug THOSE numbers into your confusers!!!

Neil Vedder


*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
--- Begin Message ---
  • From: JRawa@xxxxxxx
  • Date: Thu, 8 Nov 2007 08:41:36 EST
In a message dated 11/8/2007 1:27:55 A.M. Eastern Standard Time, esierraadj@xxxxxxxxx writes:
So, the 1956 CRL 2-dr HT D500 with 260 "advertised" horspower, but 132
dynamometer-recorded rear wheel HP, weighed 3880 lbs, and had 28"
diameter tires  (I called-around, today, and confirmed that the 1956
7.60x15" tires had virtually the same o.a. height as the 8.50x14" 1957
tires) . It had a 2-speed PowerFlite, with 2.5 Low and 1.3 Second gears,
and 3.73:1 open rear end.
hi neil..
 
out of curiosity... how was second/final gear in the powerflite not a coupled 1:1?  did you pick up on that? theres no secondary planetary set in there to accomplish that, i dont think at least... the direct clutch couples the input to output shaft, thus a "straight-thru" from converter to yoke....
 
not an attack!!!!




See what's new at AOL.com and Make AOL Your Homepage.

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1


--- End Message ---

--- End Message ---



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.