Re: [FWDLK] Different frame options for our cars?
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [FWDLK] Different frame options for our cars?



Wow, great info, thanks.

Bill Huff

At 11/4/201007:38 PM, Jim Rawa wrote:
you'd have to channel the body over the frame, or z the rear of the frame and add lowering spindles/springs up frt... ride height would end up being at least 6" higher than stock...  shoebox fords get away with S-10 chassis with a severe channel and lowering, i'm clipping the frt of a 51 ford with an 85 s-10, but z'ing the frt clip 8" to get away from the truck ride height.
 
take into consideration: a typical cars spindle centerline is between 0-4" above the runing centerline of the frame rails, i.e. the rocker panel...  a truck frame, even mini-truck, is typically 10" from the rail centerline...
 
this gives all the mercedes-banz's and camaros of the 80s craze of cars on truck frames that "extra clearance" stance of "riding on jackstands"
 
picturing the dakota, the spindle [by memory] is just in line or slightly below the rocker- so thats seems like 6" more, for say 12" from the ground to rocker panel- without modification
 
i didnt mention truck chassis in the mix in an earlier response since trucks typically would give a ride far inferior to the stock chassis.  the S-10 clip can be mellowed with g-body springs [monte carlo/grand prix etc 78-87]  i couldnt begin to know what to do with the dakota chassis/clip to make it car-worthy since those tend to run mitsubishi v-6s so i had no reason to part one.  in any case, whether S-10/ranger/or dakota.... 2wd only, unless a monster truck is on the order list for 4wd!
 
here's what a 54 chrysler looks like on a 78 olds 98 chassis.... this was all crap in a scrap pile that would have been melted down for a few toyotas... but with 5 days, $200, a 54 new yorker 2drht, 53 desoto 4dr, 56 F100, and 78 olds... this is what happens...
 
http://i81.photobucket.com/albums/j207/finned440/rattruck%20roadster/IMG_1573.jpg



-----Original Message-----
From: William Huff <whuff@xxxxxxxxxx>
To: L-FORWARDLOOK@xxxxxxxxxxxxx
Sent: Thu, Nov 4, 2010 5:41 pm
Subject: Re: [FWDLK] Different frame options for our cars?

Was thinking of measuring out a Dakota for my 58 DeSoto.

Bill Huff

At 11/4/201011:49 AM, Thy Ramirez wrote:
Howdy everyone!
Anyone use a different frame for our cars?  I am now starting to work on my 57 Dodge 2 door hardtop and would like to know what I could use with this.  Please email me with your ideas.  I would still like to use my original frame at a later date.
 
Thanks in advance!
 

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook A=1
*************************************************************
To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook A=1

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.