Re: [FWDLK] Carb Question
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [FWDLK] Carb Question



Title: Re: [FWDLK] Carb Question
I have used to JB Weld to attach a broken ‘ear’ on a AVS carb.  Did it about 5-6 years ago- no problems since...
Prep is the key to JB Weld (like anything really).  You do need to scuff the areas involved (light sanding with fine 150, 200,250 grit should do) and then make sure the mating surfaces are ABSOLUTELY clean.  I’ve used paint prep (like for wiping down a car just before you spay paint), more commonly known as degreaser/deglosser, and then after it evaporates off, apply the JB Weld.  I’ve had good luck with just brake cleaner for prep too.  It evaporates off with zero residue.  Also, make sure you are at working in at least a 65 degree area and the parts are warmed as well.  The hotter it is, the faster the JB Weld sets up.

Good Luck with it,
Charles.



On 1/20/12 6:13 AM, "Adam Lindenbaum" <AdamL57@xxxxxxx> wrote:

I have JB weld threads on the bowl (bottom,gas on them 24/7) of the center Stromberg 97 in my '27 T hot rod for about 5 years now. Did you clean and scuff the metal Ron?
Adam Lindenbaum
 
In a message dated 1/20/2012 3:51:19 A.M. Eastern Standard Time, dhomstad@xxxxxxxxxxx writes:
Ron,

I had success with JB Weld. I mixed a small ball first  and soaked it in
gasoline for a week to test if gas would attack it. It  remained hard and
firm. I applied a thick fillet around the break, not  just a film in the
crack area. It has been working now for nearly 20  years.

Dave Homstad
56 Dodge D500


On Thu, Jan 19, 2012 at  8:35 PM, Ron Waters wrote:

> In this case, it's a non-FL Olds  Quadrajet. But the answer could be
> applied to an AFB as  well.
>
> I want to attempt a repair before I have to go looking  for a
> replacement.
>
> Ron
>
> ----- Original  Message ----- From: "paul" <paulholm@xxxxxxxxxxxxx>
> To: "Ron  Waters" <ronbo97@xxxxxxxxxxx>
> Cc:  <L-FORWARDLOOK@xxxxxxxxxxxxx>
> Sent: Thursday, January 19, 2012  9:30 PM
> Subject: Re: [FWDLK] Carb Question
>
>
>>  On 1/19/2012 9:13 PM, Ron Waters wrote:
>>> In the course of  rebuilding a carburetor, a small, somewhat critical
>>>  tab
>>> broke off. The carb is made of cast  aluminum.
>>>
>>> Does anyone know of an epoxy that  will permanently glue this back ?
>>> I
>>> was sure  JB Weld would do the trick. But instead, the tab dislodged
>>>  itself within a few minutes. This was after waiting 24 hours for the  
>>> JB
>>> Weld to  dry.
>>>
>>> Ron
>>
>> what type  carb?  what application?  some are 'white' metal, an alloy  
>> and not aluminum.
>> it might be that you need a  replacement ?
>>
>>
>>
>> --
>>  Paul Holmgren
>> Mine: 2 57 300-C's in Indy
>> Hers: 05 PT  GT R/T HO Stage 1
>> Hoosier Corps L#6
>
>  *************************************************************
>
>  To unsubscribe or set your subscription options, please go to
>  http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

*************************************************************

To  unsubscribe or set your subscription options, please go  to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1

*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlookA=1 <http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook=1>


*************************************************************

To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.