Tim,
I have taken the 1956 aluminum Fury 2/4 bbl carb manifold and
sat it
down right next to the 1957 Fury 318 2/4 bbl carb manifold and
compared each
to one to the other one.
1. The aluminum 56 is much much lighter in weight than the cast
iron one.
(naturally)
2. They both take the WFCB carb's, but the 57 manifold has black cast
iron bases.
3. The ports seem to be the same size.
4. There is no counter sunk hole for the choke in the 56 but there
is in
the 57 cast iron one.
5. The aluminum manifold has a divider in the middle of the
manifold that
lets the front carb feed the front 4 cylinders and the back carb feed
the
back 4 cylinders.
6. The cast iron manifold off the 57 2/4 bbl carb manifold does not
have
the divider in it,
7. This means the aluminum manifold MUST RUN STRAIGHT LINKAGE,
however
the 57 cast iron manifold comes through from the factory with
progressive
linkage but has the option to run the linkage if you want to.
To the best of my knowledge the large single unit paper
filter used on
the D 500-1 has the same carb spacing as the 56 Fury with optional dual
carb's on the aluminum manifold. Although this large one piece paper
air
cleaner fits both Dodge and Plymouth, I do not know if it will fit
the 1956
Chrysler 300-B carb's.
Ron Allyn Swartley
PHOTO BELOW OF BOTH MANIFOLDS
56 Aluminum Fury manifold on left, other one is 57-58 Fury 318. Enlarge
this photo and you can see the P/N's
Tim, all the 11 or 16 dual 4 bbl carb Plymouth Fury's were equipped
with
stick shift. Was the same rule applied to the 56 Dodge D-500-1 cars,
also
does anybody know exactly how many 56 D-500-1 were made by the factory?
Plymouth offered a conversion kit with hotter cam and dual quads for on
the 56 Fury, Belvedere, etc.
In a message dated 12/20/2013 11:54:06 A.M. Eastern Standard Time,
DupontTim@xxxxxxx write
Furthermore, I have a big interest in the Dual Four Fury's history
because
it gave me some comparison to the D-500-1 story. I had the chase to
meet
Johnny Allen at the 50th running of the Daytona 500, the most prolific
nascar racer of Plymouths in the mid 50's (55-58). He was being
honored at the
legends banquet. He confirmed to me that Plymouth supplied to him a
complete
factory Fury racecar in may of 56. It had the Dual Four setup as well as
Imperial brakes and suspension upgrades. It was so much faster than
his 55 he
was forced to relearn his whole operation, from removing almost all
tread
from the tires to not running too hard and overheating the motor.
Also note
his hood read 260 HP after that. Great guy and still sharp. I finally
located Bernie Hentges who conformed the same experience with a
D500-1. He
picked up his car in Detroit at the factory complete with the Dual
Four Carbs
and Imperial suspension upgrades. Also note that his hood read 276
HP after
that. For those who wondered or were skeptical about these cars there is
now undisputed confirmation that both Plymouth and Dodge built factory
racecars in 1956. Drivers would eventually or even promptly modify
the cars but
they were running upon delivery or as in Brenie's case driven home to
Minnesota. Tim in Golden.
*************************************************************
To unsubscribe or set your subscription options, please go to
http://lists.psu.edu/cgi-bin/wa?SUBED1=l-forwardlook&A=1
Help the Forward Look with every eBay purchase by starting your
search here:
http://www.ForwardLook.net/eBay
Help the Forward Look with every Amazon purchase by clicking here:
http://www.ForwardLook.net/Amazon
Back to the Home of the Forward Look Network