Re: IML: crankshaft pulley repair
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: crankshaft pulley repair





I just had to rib you a little bit.  With all the dikes, wooden shoes and stuff, I was not sure that you might not have moving marks.

If the harmonic balancer from a 71 413-3 motor home engine will work, I may be able to help. 

I have one with only 36000 miles on it I am parting out.

Henry
Rob van der Es wrote:
Hahaha,
 
I see your point Henry :)
But someone suggested earlier that the rings might have slipped only once..
That means that the mark on the ring must be replaced by a new mark.
 
Unfortunately we don't have special moving marks overhere...
It might be wise to invest in a new harmonic damper, allthough there are quite hard to find for a 1960 RB 413 engine!
 
Robert
----- Original Message -----
Sent: Monday, October 16, 2006 2:48 PM
Subject: Re: IML: crankshaft pulley repair

Maybe you have special moving marks in the Netherlands, but we do not have them in the US.
 
You would need one of the special moving marks, since as the loosened ring moves, the mark would have to move on the ring to be correct. 

Unlike a broken watch, the fixed mark on the damper would not even be right twice a day.

Henry

Rob van der Es wrote:
Why is it such a problem then if the outter ring has slipped?
I mean, you only have to find TDC of the #1 cyl and make a new mark on the
ring???

Or do I miss something here?

Thanks,

Robert




Op Vr, 13 oktober, 2006 7:52 pm, schreef DR CHALLENGER:
  
if thats true the damper is junk, needs to rebuilt or replaced.


    
From: "Dave" <Wilkerbeast01@xxxxxxxxxxx>

      
It can if the outter ring has slipped on the inner ring.


David C. Wilker Jr. USAF (RET)


--- My memory's not as sharp as it used to be.
Also, my memory's not as sharp as it used to be.


----- Original Message ----- From: "DR CHALLENGER"
<drchallenger@xxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Thursday, October 12, 2006 2:17 PM
Subject: Re: IML: crankshaft pulley repair



      
The damper only goes on 1 way, it cant be 180 degrees off.



        
From: David Whitney <hazegreen66@xxxxxxxxx>
)






When you change the balancer, you MUST be certain that the TDC mark
 (the one you use to set timing) is actually pointing to 0 on the
plate affixed to the timing chain cover when cylinder 1 is at EXACT
top dead center on the COMPRESSION cycle.  The most common mistake
is getting it 180 degrees out.  Having it off by a few degrees will
merely make it difficult to set the timing because you won't want to
believe your eyes when you see how many degrees initial advance you
have.

Some of what I have written is merely interesting.  The important
sentences have words in CAPS.  Not abbreviations... words.

          
-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared
with everyone. Private messages (and attachments) for the Administrators
should be sent to webmaster@xxxxxxxxxxxxxxxx To UN-SUBSCRIBE, go to
http://imperialclub.com/unsubscribe.htm



    




-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please 
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be 
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm


  


No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.408 / Virus Database: 268.13.4/476 - Release Date: 14-10-2006



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.