Re: IML: 56 Ignition Problem
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: 56 Ignition Problem



Burned points can also result from touching the contact surfaces with your fingers. Any oil or lube from the rubbing block will also burn them prematurely. Clean the surfaces thoroughly if in doubt, especially if buying NOS parts from someplace. Who knows how many times they have been out of the box and handles by some lunck head before selling them to you.

They can LOOK pretty bad and still work. Could you poor performance be due to them being improperly gapped? The setting is .015 - .018 and they both need to be the same. That can be tricky on the dual point distributor. They have to be gapped separately and only when each set is fully planted on a ridge at the rubbing block.

Normal point life is about 15,000 miles. Once you have done it a few times it isn't too bad. On '55 and '56 it is easier to remove the distributor since you then have control over the position of the point sets in relation to the rubbing block. Accuracy is imperative. Also, with the distributor mounted on the back of the motor at 15 years old I had no trouble crawling around under there, but at 55, its not easy. Just mark everything so you know where it should be when your done, and crank the engine over in the meantime.

Paul W.

-----Original Message-----
From: a292@xxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Tue, 6 Feb 2007 4:52 PM
Subject: Re: IML: 56 Ignition Problem

The ballast resistor is there to limit current. The voltage drop is simply a side effect of the limited current that the ballast allows to pass through. It's the limited current that prolongs the life of the points.

Any resistor will show the same voltage on both sides until a load is applied. It's sort of like if you connect a garden hose with a spray nozzle on the end to a spigot. You can hold the spray nozzle open and turn the spigot on until there is just a trickle of water coming out of the nozzle. The pressure in the hose is very low. Now turn the spigot off and the pressure in the hose will build up until it matches the pressure in the pipe supplying the spigot. Turn the nozzle back on and the pressure in the hose rapidly drops again. A similar thing is happening with the voltage in your ignition system except that it happens almost instantaneously. A big difference in the ignition system is that unlike the garden hose which will briefly allow a large quantity of water through the nozzle, the ballast will not allow a large flow of current to pass through. I'm not very good at explaining it and that's not the greatest analogy but I hope it makes since.

In any case I would try a different condenser. I have had a bad condenser in the past and the engine would still run but not very well and it causes a LOT of excessive arcing across the points when they open which will fry them in short order. Also the output voltage of the coil will be very low which is why the engine will run so roughly. The job of the condenser is to allow the magnetic field in the coil to collapse in a controlled manner. It allows the voltage in the primary windings to rapidly but not instantaneously fall. It's this collapsing of the voltage and hence the magnetic field which produces the high voltage in the secondary windings to fire the plugs.

Have a good day
Brad

On Feb 6, 2007, at 5:17 PM, Jeff Cantor wrote:

Brad,

Thanks for the suggestion although it has me puzzled. I was under the
> impression that when electrical systems went from 6V to 12V in the > mid-50s, the ignition systems were kept at around 6V to avoid having > to beef up the points. If there is still supposed to be 12V across > open points, then you're going to have much greater arching across > those points as they close hence the damage that I've observed. > Wouldn't 6V across those open points produce less arching and > therefore less damage?

Jeff
'56 Sedan
Trenton, NJ


----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm

________________________________________________________________________
Check out the new AOL. Most comprehensive set of free safety and security tools, free access to millions of high-quality videos from across the web, free AOL Mail and more.


-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.