Re: {Chrysler 300} Top Dead Center

[John Grady <jkg@xxxxxxxxxxxxxxxxx>]

it is very hard to judge by eye to the accuracy you need if doing this for ignition - on a hemi I found that I think it was a 3/8 or 1/2 socket extension just fits plug hole  ( be sure spotless ) and you can puta dial indicator on top of it . rough position it by eye then you see dial indicator come up and then reverse . Do it from both directions if at all different by a degree go in middle . 

related , to be sure on power stroke — you can feel difference in air pressure , or if un disturbed — look at rotor . When on #1 tdc , slot for distributor is parallel to block , on either of the two TDC —  if cam  gear in right — but distributor can also go to slot two ways  . Combination of all this can confuse . 

So slot straight , power stroke TDC , rotor at #1 

On wedge the piston stop method probably best , that tool is cheap stuff . 

J 

Sent from my iPhone not by choice 

On 14 Mar 2021, at 12:25 am, Ray Jones <1970hurst@xxxxxxxxx> wrote:

A straw.   Remove  #1  plug.

With the distributor cap off, the rotor will tell you if it is near #1.

Bring the crank slowly up to #  1 marked  on the pulley, stick the straw into the plug hole, and  SLOWLY bring  the crank around watching the straw. It will push up out of the hole and when you pass the TDC, it  will start going down.

This is about as accurate as you can get as you are watching the piston travel.

Ray

On Sat, Mar 13, 2021 at 1:53 PM Ron Kurtz <mark6268@xxxxxxxxxxxxx> wrote:

Hello, everyone:

Which is the most accurate top dead center tool for an engine already installed? Been a while since I last used one.

Best,
Ron Kurtz
E #292

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/79172488.477414.1615665208520%40mail.yahoo.com.

--

Ray Jones. Y'all come on down an see us. Ya hear?

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CAD72c-y4OudMHuhKkJ75cGomYxPJZ-W%3D8m6kVPoE3FoM__pgQA%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/F3FF547F-B7AD-4682-B9DC-B109A4CF04E7%40gradyresearch.com.